Wire and cable bundle combustion tester

info@qinsun-lab.com Get Quote

Product Introduction:

The wire and cable bundle combustion tester is designed according to the requirements of UL1685 and GB18380.3 standards for wire and cable bundle combustion tests. And comply with IEC 60332-3-10, KS C IEC 60332-3-21-25 (Class A to D) standards. In addition, if the burner of this tester is adjusted by 20 degrees, it can meet the testing standards of IEEE 383 (IEEE 1202). The equipment can be equipped with a heat release instrument configuration port, which can be used in conjunction with a gas analysis device to measure thermal power values, such as H.R.R (heat release rate) and S P. R (smoke generation rate), etc.

Applicable scope:

The single vertical flammability tester for wires and cables is suitable for testing the flame retardant performance of the insulation layer of wires and cables under abnormal conditions such as overheating and overcurrent under flame conditions. It can be applied to the vertical flame spread test of wires, cables or optical cables, and can also verify the combustion status of droplets under flame conditions.

1. IEC 60332-3-10 Tests for cables and optical cables under fire conditions: Vertical flame propagation test for vertically installed bundled wires or cables;

2. EN 50399 General testing methods for cables under fire conditions;

3. IOS18380.31-2008 and IEC60332-3-10-2000 quot;Fire tests for cables and optical cables under flame conditions - Part 31: Test report on vertical flame propagation of vertically installed bundled wires and cables - Test apparatusquot;;

4. IOS18380.32-2008/IEC60332-3-21:2000 quot;Fire tests for cables and optical cables under flame conditions - Part 32: Vertical flame propagation test for vertically installed bundled wires and cables - Class AF/Rquot;;

5. IOS18380.33-2008/IEC60332-3-22:2000 quot;Fire tests for cables and optical cables under flame conditions - Part 33: Vertical flame propagation test for vertically installed bundled wires and cables - Class Aquot;;

6. IOS18380.35-2008/IEC60332-3-24:2000 quot;Fire tests for cables and optical cables under flame conditions - Part 35: Vertical flame propagation test for vertically installed bundled wires and cables - Class Cquot;;

7. IOS18380.36-2008/IEC60332-3-25:2000 quot;Fire tests for cables and optical cables under flame conditions - Part 36: Flame spread test for vertically installed bundled wires and cables - Class Dquot;;

User experience:

1. High level of intelligence and simple operation;

2. Professional industrial design, beautiful and elegant;

3. Accurate, safe, and stable equipment;

4. Micro computer control system, intelligent testing process; No need for manual timing and related operations;

5. Stainless steel corrosion-resistant housing.

Product features:

Box features:

1. The size of the stainless steel test box is 1000 plusmn; 100 (W) x 2000 plusmn; 100 (D) x 4000 plusmn; 100 (H) mm. The inner surface of the box is higher than the ground, and there is insulation material laid on the back side.

2. Equipped with stainless steel ladders in accordance with standard requirements and steel ladders in accordance with IOS18380.31;

3. Two spare sample racks;

4. The material of the steel ladder is stainless steel; Corrosion resistance; Easy to clean;

5. At the lower part of the box, there is an 800 plusmn; 20 (W) x 400 plusmn; 10 (D) air inlet located 150 plusmn; 10mm away from the front of the box.

6. There is a K-type armored thermocouple installed on the inner side of the box, with a diameter of 2mm

7. The air flow rate inside the combustion furnace can be stably controlled at (5000 plusmn; 500) L/min.

8. Stainless steel smoke exhaust pipes and related accessories;

Combustion system:

1. Burner: Belt type propane gas nozzle, size 257mm x 4 5mm, a total of 242 holes were opened, arranged in three rows, with 81, 80, and 81 holes respectively. The diameter of the holes was 1.35mm, and the distance between the holes was 3.2mm;

2. High precision ball valve, controlling gas on/off;

3. Dual flow meters: air flow and gas flow meters and control valves;

4. The front end of the combustion tester is equipped with a flame cut-off cylinder to prevent propane gas from backfiring, thereby ensuring the safety of the sample to the greatest extent possible

5. Burning angle: horizontal; Automatic ignition device; (20 degrees adjustable as optional)

6. The air and gas flow rates in the burner must be supplemented with temperature and pressure, which many traditional systems ignore and can automatically complete the gas and air compensation process through computer programs.

Control system:

1. PLC combined with large touch screen control system;

2. The system automatically ignites and timing; Timing range 999min, accuracy 1s;

3. Experimental data is automatically stored and can be freely queried;

4. 40 minutes, 1-hour timer reminder function;

5. The sample installation bracket is lifted and lowered using an electric crane.

Technical parameters:

Box size: 1000 plusmn; 100 (W) x 2000 plusmn; 100 (D) x 4000 plusmn; 100 (H) mm

Anemometer accuracy: 0.1m/s

Air source anemometer range: 8000L/min

Air outlet speed: (5000 plusmn; 500) L/min (adjustable)

Burner size: 257mm x 4 5mm

Gas: Technical grade propane with a purity of 95% (to be provided by the customer)

Gas control flow direction: 100kpa, under 20 ℃ conditions

Combustion gas source: propane (or liquefied petroleum gas)

Size: 1165 (W) x 2165 (D) x 4350 (H) mm

Console size: 600 (W) x 750 (D) x 1600 (H) mm

Power supply: AC 220V, 50/60Hz, 15A

Weight: 1500kg