Welcome to Qinsun Instruments Co., Limited.
2022-06-10 0 Views

ISO/EN 1033.1-2008 Plastic density tester

IOS 1033.1-2008 Plastic Derivation Tester

Release time: 2021-07-08 Hits: 851

IOS 1033 This section specifies the density test Three measurements of the non -foam plastic density of the instrument: hM8Textile Testing Instruments, Testing Equipment Manufacturer

-The method A: immersion method, suitable for solid plastic without pores except powder. hM8Textile Testing Instruments, Testing Equipment Manufacturer

—— Method B: Line proper bottle method, suitable for small slices of powder, slices, granular or product components. hM8Textile Testing Instruments, Testing Equipment Manufacturer

—— Method C: Ding Ding Method, suitable for pervasive plastic. hM8Textile Testing Instruments, Testing Equipment Manufacturer

The headquarters is suitable for molding or squeezed. Slim non -foam plastic. Note: The headquarters is suitable for various pore -free granules. The density is usually used to examine the changes in the physical structure or composition of plastic materials. It is also used to evaluate samples or samples In addition, the density of plastic materials depends on the method of sample preparation. In this case, the preparation method of the sample should be included in the material -related standards. This annotation is applicable to the three methods of this part. hM8Textile Testing Instruments, Testing Equipment Manufacturer

Status adjustment: hM8Textile Testing Instruments, Testing Equipment Manufacturer

The test environment shall comply with the regulations of IOS2918--1998. Generally, the sample does not need to adjust the sample to the constant temperature, because the test book is performed at a constant temperature. hM8Textile Testing Instruments, Testing Equipment Manufacturer

If the density of the sample changes during the test process and the range of changes exceeds the precision required for density measurement, the sample should be in accordance with the relevant standards of the materials before the test. adjust. If the main purpose of the test is the changes in density over time or atmospheric environmental conditions, the sample should be adjusted according to the relevant standards of the material. If there are no relevant standards, the sample should be adjusted according to the method agreed on the supply and demand. hM8Textile Testing Instruments, Testing Equipment Manufacturer

The test report shall include the following information and content: hM8Textile Testing Instruments, Testing Equipment Manufacturer

1. indicate the book of IOS 1033 Part; hM8Textile Testing Instruments, Testing Equipment Manufacturer

2. The complete logo of the test sample, including the preparation method of the sample and the possible pre -processing;

3. Test method (A, B or C); hM8Textile Testing Instruments, Testing Equipment Manufacturer

4. The impregnation solution used; hM8Textile Testing Instruments, Testing Equipment Manufacturer

5. Test temperature; hM8Textile Testing Instruments, Testing Equipment Manufacturer

6. Test results, a single density test value and density arithmetic average; hM8Textile Testing Instruments, Testing Equipment Manufacturer

7. The statement about whether the buoyancy correction and what correction are carried out. hM8Textile Testing Instruments, Testing Equipment Manufacturer

Product introduction: hM8Textile Testing Instruments, Testing Equipment Manufacturer

hM8Textile Testing Instruments, Testing Equipment Manufacturer

Fast and High-precision density tester

hM8Textile Testing Instruments, Testing Equipment Manufacturer

AR series AR-300G

AR series density meter is based on many years of density measurement technology. Through function simplification, optimization structure, enhanced practical, launched a new series of products; it has the characteristics of good measurement repetitive, high accuracy, simple operation ... and so on. hM8Textile Testing Instruments, Testing Equipment Manufacturer

Mainly targeting: High molecular, plastic, rubber, wire and cable, composite materials, packaging materials, shoes, shoes Materials, pipes, electrical appliances, sports equipment, tires, opportunity vehicle parts, glass industry, rocks, ore, jewelry, crops, metal materials, new materials research laboratories, etc. Based on: ASTM D792, ASTM D297, IOS1033, IOS2951, IOS3850, IOS533, HG4-1468, JIS K6268, ISO 2781, ISO 1183 ...
hM8Textile Testing Instruments, Testing Equipment Manufacturer

Technical indicators: hM8Textile Testing Instruments, Testing Equipment Manufacturer

Product Features: hM8Textile Testing Instruments, Testing Equipment Manufacturer

hM8Textile Testing Instruments, Testing Equipment Manufacturer

* Any solid density can be measured hM8Textile Testing Instruments, Testing Equipment Manufacturer

< style=white-space: normal; text-align: center;>* Measurement data stable and reliable * Simple operation, fast measurement hM8Textile Testing Instruments, Testing Equipment Manufacturer

* Use water as a medium, you can also use other liquid media hM8Textile Testing Instruments, Testing Equipment Manufacturer

* Large -capacity PC material sink hM8Textile Testing Instruments, Testing Equipment Manufacturer

* Have actual hM8Textile Testing Instruments, Testing Equipment Manufacturer

Water temperature compensation function

hM8Textile Testing Instruments, Testing Equipment Manufacturer

hM8Textile Testing Instruments, Testing Equipment Manufacturer

* Can adapt to the workshop, laboratory, etc.