Welcome to Qinsun Instruments Co., Limited.
- +86-21-6780 0179 |
- info@qinsun-lab.com |
- Customer Services
The load capacity of the anti -static activity floor, let's introduce the anti -static activity floor first.
Anti -static activity floor is composed of the floor section and floor support system. The floor of the anti -static activity can be divided into surrounding support and four -corner support according to the support method. It is mainly composed of substrate materials, outer layers, anti -static surface materials and auxiliary components.
The floor section of the anti -static activity floor is divided into wood, inorganic, steel, aluminum, values (polymer materials) and other classes.
The floor section of the anti -static activity floor is divided into ultra -light, light, ordinary, standard type, heavy and overweight.
Anti -static surface material wear resistance resistance requirements require the abrasion resistance of melamine (HPL) surface, The regulations of IOS 4085, anti -static ceramic surface wear resistance should comply with the regulations of IOS 26539, and other types of veneer can be implemented according to user requirements.
Anti -static activity The test equipment of the rolling load of the floor rolling wheel shall meet the following requirements:
1. Rolling test equipment (the equipment itinerary is greater than 2m, the rolling speed is 15m/min ± 5m/min, the load capacity is 0N ~ 7000N); With the peak maintenance function, the accuracy is 3%), you can also use the X-Y function recorder;
The rolling load test of the anti-static activity floor section shall be performed according to the following test steps:
1. Place the actual installation status of the three test sectors on the rolling load test machine of the anti -static activity floor, adjust the level and gap and use a fixture to fix the test sector;5. Install the displacement sensor on the bottom surface of the lower panel of the intermediate test sector, and in the same axial position as the roller wheel, to make the displacement sensor closely in contact with the bottom surface of the test sector and zero;
3. Add load to the specified roll
Dynamic load value, start the anti -static activity floor rolling load test machine, use the A rolling wheel rolling 10 times, the large deformation of the bottom surface of the lower panel is the rolling load, The deflection of the rolling wheel is removed and the residual deformation of the test sector is recorded after the rolling wheel is removed 1min.At the fundamental, insist on using products and services to impress customers and achieve common development and progress.
1. Product introduction:
Floor rolling wheel test machine
Also known as floor foot wheel wear durability test machine, floor ramp wear test machine, also known as floor -to -foot wheel effect measurement meter, etc. This test machine is widely used for testing PVC, SPC, WPC flooring wheel wheels The abrasion resistance, rubbing the floor samples under a certain speed, a certain load, a certain motion trajectory through a certain specifications, and the accumulated test of the cumulative test is completed to observe the change of the sample. Cumulative cycle counting, the number of cycles can be set, and the pressure time can be set!2. Reference standards:
1. BS EN 425-2002 (R2012): Resilient and laminal floor caverings -Castor Chair Test elasticity Floor coverage. The determination of the chair foot wheel effect
2.BS EN 985-2001 Textile Floor Coverings -Castor Chair Test paving fabric.3.ISO 4918-2016Resilient, Textile and LAMINATE FLOOR COVERINGS-Castor Chair Test Elastic Layers-Athlete Wheel Chair Test
4.So 10581-- 2011 Resilient Floor Coverings-Homogeneous Poly (Vinyl Chloride) Floor Covering-Specification Elastic Carpet-Memorability Polyethylene Carpet-Specification5.Ansi-nalfa-LF- 01-2008.3.6/ANSI-NALFA-LF-01-2011 Castor Chair Resistance--North American Composite Floor Floor Foot Rollery Test
6.ansi-nalfa-LF-01 -2011 Floor floor coverage test test
7.IOS 2611-2007: General Technical Requirements for Testing Machines..
8. IOS 5226.1-2008: Some general technical conditions for mechanical electrical safety machinery and electrical equipment.
